Set up a new sensor

  1. 1

    Create a Garge account

    Go to www.garge.no and select “Create account”.

    You need an active subscription to add sensors.

  2. 2

    Get a pairing code in the app

    A pairing code is a one-time code that links the sensor to your account.

    1. In “My Devices”, select “+ Add device”. On a phone, the button only shows “+”.
    2. Select “Get pairing code”.
    3. Keep the page open.

    The code has 6 characters and lasts 15 minutes.

    My Devices with the plus button at the top right
    “+” in “My Devices” on a phone.
    Add a device showing a pairing code
    Your pairing code appears here.
  3. 3

    Power on the sensor

    Garge Sensor: connect it to power with a USB-C cable.

    Garge Voltmeter: connect it to the SAE plug on the 12 V battery.

    The blue light blinks fast when the sensor is ready. Not blinking fast?

  4. 4

    Connect the sensor to Wi-Fi

    1. In your phone's Wi-Fi settings, join “Garge …”, for example “Garge a1b2c3d4e5f6”.
    2. The setup page opens. If it does not, go to 192.168.4.1 in your browser.
    3. Choose your Wi-Fi network and enter its password.
    4. Enter the pairing code.
    5. Select “Connect”.

    If the page shows “Pair device”, the sensor already has a Wi-Fi network saved. See what to do.

    The sensor’s Wi-Fi Setup page
    The setup page on your phone.
  5. 5

    Name the sensor in the app

    1. Go back to “My Devices”. The sensor appears automatically within a couple of minutes.
    2. Give it a name, for example “MC battery”. How to rename a sensor.

    If it does not appear, reload the page. Still not showing?

Something is not working

Problems during setup

Your phone cannot find the “Garge …” Wi-Fi network

How to fix it

  1. Open setup mode on the sensor.
  2. In your phone's Wi-Fi settings, look for “Garge …” again. The network is open, so you do not need a password.

Setup mode lasts up to 30 minutes.

The sensor's setup page does not open

How to fix it

  1. Stay connected to “Garge …”.
  2. In your browser, go to http://192.168.4.1.

The sensor's setup page only asks for a pairing code

How to fix it

  1. Enter a new pairing code.
  2. Select “Pair”.

To choose another network, select “Change Wi-Fi” instead.

The page shows “Pair device” because the sensor already has a Wi-Fi network saved. The first setup page says “Pairing code (optional)”, but a new sensor needs the code. If you left it empty, the sensor goes into setup mode again so you can enter it.

The pairing code has expired

How to fix it

  1. If you see “This pairing code has expired.”, select “Get new code”. The old code stops working.
  2. If you already entered the old code on the sensor, open setup mode. Then join “Garge …” on your phone and enter the new code. Read more about the “Pair device” page.

Closed the page? Get a new pairing code.

A code lasts 15 minutes, and you can only use it once.

You cannot get a pairing code in the app

How to fix it

If you see “You need an active subscription to add more devices.”, select “See plans”. The sensors you already have keep working.

If “Sensor capacity” under “Profile” says “At capacity”, turn a sensor off or add capacity.

A new sensor does not show up in the app

How to fix it

Check that your network is on 2.4 GHz and not hidden. The sensor only supports 2.4 GHz Wi-Fi. The setup page only lists the networks it finds. If your network is hidden, make it visible. If it is 5 GHz only, use a 2.4 GHz network.

If the password may be wrong, do this:

  1. Get a new pairing code in the app first. Your phone has no internet while it is connected to the sensor.
  2. Open setup mode on the sensor.
  3. On your phone, join “Garge …”.
  4. On the “Pair device” page, select “Change Wi-Fi”.
  5. Choose the network, and enter the password and the new code.
  6. Select “Connect”.

The setup page does not test the password. It only says “Data received. Restarting...” A sensor with a wrong password does not go back to setup mode by itself.

Problems after setup

The sensor has stopped sending readings

How to fix it

  1. Check that your Wi-Fi network works.
  2. In “My Devices”, select the sensor. “Last seen” shows when it last sent a reading.
  3. If the network name or password changed, change the Wi-Fi network on the sensor. The sensor does not find the network by itself.
  4. If a card is marked “Off” in “Profile” > “Manage sensors”, its readings are hidden. Select “Turn on”.

A Garge Sensor keeps trying to reconnect by itself. It also blinks slowly while it tries, so a slow blink does not always mean it has Wi-Fi.

A Garge Voltmeter that cannot connect sleeps longer between tries, up to 6 hours. After your Wi-Fi works again, it can take up to 6 hours for the voltmeter to show up in the app again. To skip the wait, press the Restart button. The voltmeter then tries to connect at once.

A Garge Voltmeter does not respond to the buttons

How to fix it

Press the Restart button to wake the voltmeter. To change its Wi-Fi network, open setup mode.

The voltmeter sleeps between readings and ignores the BOOT button while asleep.

Alerts from Garge do not arrive

How to fix it

  1. Check that “Offline alerts on this device” is on in the browser or app you use.
  2. Select “Send test”.

If you see “Notifications blocked in browser settings.”, allow notifications for Garge in your browser.

If you see “Push notifications are not supported in this browser.”, use another browser. On iPhone, first select “Share” > “Add to Home Screen”, then open Garge from there.

Still stuck? Contact us.

Common tasks

Change the Wi-Fi network on a sensor

  1. Open setup mode on the sensor.
  2. On your phone, join “Garge …”.
  3. Select “Change Wi-Fi”.
  4. Choose the new network and enter its password.
  5. Leave the “Pairing code (optional)” field empty. You do not need a new code when the sensor is already on your account.
  6. Select “Connect”.

Get an alert when a sensor goes offline

  1. Go to “Profile” > “Notifications”.
  2. Turn on “Offline alerts on this device”.
  3. Under “Alert after”, enter the number of hours, from 1 to 168.
  4. Select “Send test” to check that alerts reach you.

The switch only applies to the browser or installed app you are using now. Turn it on in each one where you want alerts. “Alert after” applies to your whole account.

A Garge Voltmeter sends a reading about once an hour, so choose more than 1 hour for it.

The Notifications settings with Offline alerts on this device, Alert after and Test notification
The notification settings.

Share a sensor with another user

  1. Go to “Profile” > “Manage sensors”.
  2. On the card you want to share, select “Share”.
  3. Enter the email address of another Garge user.
  4. Choose “Read” if the other user should only see the readings. Choose “Edit” if the other user should also be able to create automations for the sockets the sensor has found.
  5. Select “Share”.

You share one card at a time. A Garge Sensor has two cards, temperature and humidity. Share each card the other user should see.

To stop sharing, open “Share” again and select the X next to the person under “Shared with”. Only the owner can share a sensor. The other user can remove the share by selecting “Leave” on the card.

The Sensors page with Share and Remove from account on each card
Each card has its own “Share” and “Remove from account” buttons.
The Share dialog with an email field and a Read or Edit choice
Enter the email address and choose “Read” or “Edit”.

Rename a sensor

  1. In “My Devices”, select the sensor.
  2. Select the pencil next to its name.

A name can have up to 50 characters. Each card has its own name, so a Garge Sensor has one for temperature and one for humidity.

In “Profile” > “Manage sensors”, you can also select the pencil on the card.

A sensor opened from My Devices, with a pencil next to its name
The pencil next to the name.

Sell or give away a sensor

  1. Go to “Profile” > “Manage sensors”.
  2. On each card, save the code under “Device code”. The code disappears when you remove the card. A Garge Sensor has two codes.
  3. On every card for the sensor, select “Remove from account”.

A Garge Sensor has two cards, temperature and humidity. If one stays, the new owner gets only part of the sensor and you keep access to the rest.

Cards from the same sensor have the same code in their default name, for example “Garge D4E5F6 temperature” and “Garge D4E5F6 humidity”. If you renamed a card, its default name is on the “Default:” line.

Removing a card deletes its custom name, photos, activities and thresholds from your account. Anyone you shared it with loses access. You can add the sensor back later with the code under “Device code”. This needs an active subscription.

What the new owner does

  1. Follow setup steps 1 and 2.
  2. Power on the sensor.
  3. Open setup mode on the sensor.
  4. On the phone, join “Garge …”.
  5. On the “Pair device” page, select “Change Wi-Fi”.
  6. Choose the Wi-Fi network.
  7. Enter its password and the pairing code.
  8. Select “Connect”.
  9. Follow setup step 5.

The new owner does not see the seller's readings. The seller's Wi-Fi name and password stay on the sensor until the new owner's Wi-Fi replaces them.

The buttons and light on the sensor

Where to find the BOOT and Restart buttons

The buttons are behind two small holes on the case. The case has no labels. BOOT is behind the upper hole and Restart is behind the lower hole.

BOOTRestart
The buttons on the sensor.

How to open setup mode on the sensor

In setup mode, the sensor creates its own Wi-Fi network, “Garge …”.

  1. Press the Restart button and let go.
  2. Straight away, hold the BOOT button until the light blinks fast.

This can take more than 5 seconds. If it does not blink fast, try again. Opening setup mode erases nothing.

If the light does not come on at all, check the power. For a Garge Voltmeter, check the battery and the plug. If the light is still off, press the Restart button once more.

If the sensor is already set up, you can leave setup mode at once. Press the Restart button.

What the blue light on the sensor means

LightWhat it meansWhat to do
Fast: 1 s on, 1 s offThe sensor is in setup mode. This lasts up to 30 minutes.Connect the sensor to Wi-Fi.
Slow: 5 s on, 5 s off (Garge Sensor)The sensor is running. The light also blinks like this when Wi-Fi is not working.Nothing. Getting no readings?
Short blink (Garge Voltmeter)The sensor wakes, sends a reading and sleeps again.Nothing.